How To Atmega Loader(PicByPic)/ Como usar el Atmega Loader (foto a foto)

[bicholas]

How To Atmega Loader(PicByPic)/ Como usar el Atmega Loader (foto a foto)

Basic Guide./ Guía Básica
By Bicholas

Thanks to Lexus, Wicked Team and Coranger.
Gracias a los antes mencionados.

This tool has exceptional features not covered in this how to, this guide is for newbies.Is not a Complete or offical guide.

Esta herramienta tiene funciones excepcionales que no serán cubiertas en esta guía, ya que esta hecha para principiantes. No es una guía completa u oficial.


Before start: If your atmega has jumper, take it off you don´t need it anymore.
Antes de empezar: si tu atmega tiene un jumper, quítaselo, no lo necesitarás más.


1. Connect atmega programmer to lpt port and insert atemga, start program. If you didn't insert atemega or programmer is not properly connected you will get this:

Conecta el programador de atmegas al puerto Lpt e inserta la atmega, corre el programma. Si no insertaste la atmega o tus conexiones no son correctas verás esto:






2. Double check connections and make sure Atmega is all the way in the programmer then go to menu and select atmega and click on detect card or press F9.

Revisa tu conexiones y asegurate que la atmega este bien insertada, ve al menú y selecciona Atmega y da click en Detect Card o presiona la tecla F9.







3. Now you Card is detected and ready to start programming.

Ahora tu tarjeta esta detectada y lista para programarse.







4.Go to menu and click on settings. Make sure your screen looks like this and click ok:

Ve al menú y da click en settings. Asegúrate de que tu pantalla sea igual a esta y luego da click en Ok.






5.Now click on Run Wicked Wizard button.

Haz click en el botton que dice Run Wicked Wizard para empezar a programar.






6. Click on Dishnetwork then next.

Haz click on Dishnetwork.







7. Set to expire in 60 days, select your time zone,DT and Zip Code, Select your tiers by clicking on them,DO NOT touch "next" button then click on the red arrow on top, this will bring you more tiers (channels).Make sure you scroll the next windows down, that way you can see all the tiers and select those you want.


En donde dice set to expire: escribe 60, selecciona tu zona de tiempo, si usas tiempo de verano (DT), Tu código Postal, Selecciona tus canales haciendo click en los nombres. NO presiones el boton Next aún. En la parte superior derecha se encuentra una flecha roja, dale click para ver mas canales y selecciónalos. Asegurate de recorrer hacia abajo todas las ventanas siguientes, de esa manera verás todos los canales disponibles y podrás seleccionarlos.







8. This is the locals screen. IE, You wanna get Albany GA locals. Click on Albany GA.

Esta es la pantalla para escoger locales, por ejemplo tu quieres tener los locales de Albany, Ga.







9. If you wanna your locals remapped (located under100's channels). When you left click on square of Albany GA you'll get the rempap to this local option, click on it. After that You can press "next" button.

Si quieres que tus locales sean reubicados en los canales anteriores al cien, cuando selecciones el cuadrito de Albany, GA, te aparecerá la opción "remap this local", dale click. Ahora si PRESIONA el botón "next". Observa la imagen.







10.Select proper keyset: No rsa, Tomico, etc. Don't Use Private Numbers, unless you know what what you are doing, you may want more info on what you need to use Private numbers.

Selecciona el tipo de modificación que tiene tu receptor o deco: No rsa, tomico, etc. No uses la opción "private keyset" a menos que sepas lo que estás haciendo. Para usar esta opción necesitas averiguar qué necesitas para poder usarla.

[bicholas]

11. Select Xtal Speed.(little silver thing on atmega)

Selecciona la velocidad del reloj o cristal de la atmega (la cosita ovalada y plateada)








12.Keys are retrived automatically. Click Next button.

Las llaves o códigos son cargados automáticamente. Haz click en el botón "next"







13. Click on "write card"

Haz click en "write card"








14. wait A few minutes and you'll get:

Espera unos minutos y tendrás:








15. ...And You are ready To go!

...¡¡¡Listooooooooooooooooooooooooo!!!

PS: Press add PPV buton and write:

PPV Low: 0010000
PPV High: 0099999
Thanks warren on for this info.
Thanks for inviting me to this site Onehipgirl!

[adf]

hi
can i use on key set ,rom10to102
thank`s

[learn key]

rom10 doesn't work right now

[Pinksforslips]

Originally Posted by adf

hi
can i use on key set ,rom10to102
thank`s

Yes

[Z-GUY]

Just a question..how does the wicked loader 5.1 know which pfg script to run? How does one do it? I used for the first time today following the instructions on this thread..I just had to check switch and its up and running.

[elliott2ride]

wow! sorprendido<,

[FTA_Rooky]

I just get this recever with the card because my friendès wife did not like to have all the chanels in the house. I was able to program the card using Jeeper and it worked with other recever but it showed Wrong card in the recever when I inserte it into my recever. How can I get it to work with my recever. Where can I get this WICKET Loader if I have to load the program with it and where can I get the new bin files.. HELP

[klondine]

Originally Posted by FTA_Rooky

I just get this recever with the card because my friendès wife did not like to have all the chanels in the house. I was able to program the card using Jeeper and it worked with other recever but it showed Wrong card in the recever when I inserte it into my recever. How can I get it to work with my recever. Where can I get this WICKET Loader if I have to load the program with it and where can I get the new bin files.. HELP

Just get a pfg AR using jeeper and that's it !!,

[sunny14]

is there a different programmer to work with this loader. The way I program my Atmega is i have LPT printer cable and this little device which connects to. Are u referring to the same programmer or different